Filters

Secure Checkout
We are shipping today , Free Shipping On Orders Over $50
Your Shopping Cart Is Empty

Secure Checkout

SKU: KIT-PAM1270MULTIIR PAM1270 12x Channel, 6x Zone 70V/100V/8 Ohm Commercial Multi Combination Amplifier with IR Remote


Purchase PAM1270 12x Channel, 6x Zone 70V/100V/8 Ohm Commercial Multi Combination Amplifier with IR Remote
  • SKU: KIT-PAM1270MULTIIR multi-zone-amp-8ohms-70v-switchable-12-channel-pam1270

    PAM1270 12x Channel, 6x Zone 70V/100V/8 Ohm Commercial Multi Combination Amplifier with IR Remote

  • $699.99

    Compare at: $999.99 You Save $300.00

    In Stock

Calculate Shipping

Guarantee

Lifetime Tech Support

The OSD PAM-1270 is a major step forward in installation amplifiers technology. It features either Twelve Zone mono channels (70V) or Six Stereo Zones (8/4 Ohm) or a combination of both 70V and 8/4 Ohm 85% class D design technology, can operate as 6 independent Stereo Zone amplifiers. Self-explanatory Input and Output connections are easy to follow since any of the 12 mono amplifiers can be connected to either 70-Volt, 8-Ohm or 4-ohm speaker circuits.

Each of the 12 mono amplifiers has their own input and output connectors and level Controls. Up to 6 stereo Zones (4-ohm or 70-Volt at 50Watts/channel), 6 mono/bridged Zone amplifiers (110 Watt bridged 8-ohm). Each zone can be configured independently allowing a combination of Stereo 4-ohm or 70Volt and Mono/Bridged 8-ohm. Dual-function LEDs on the front panel provide both activity and Clip indication for each pair of amplifiers. Additional features selectable on the back panel include Six Limiter Button and Six Stereo/Bridge modes for the individual Stereo or Bridged Mono Zones. The Channel Input Line/Bus switch selects between either the Bus Input (button depressed) or the individual Zone's Input signal.

The PAM-1270 includes a RS232 for IP interface with Home Automation Systems Additional features include: any amplifier with no signal at its input is automatically shut off and the CA1250 is Multi Voltage; able to operate either on 110V-120V/60Hz or 220V-240V /50Hz AC mains.

Warning: California's Proposition 65

Warning:

This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP) which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

  • Design Type: Class D
  • Peak Power Output: 60 Watts per channel
  • Maximum 8 ohm stereo output power at less than 0.1% THD+N: 30W
  • Maximum 4 ohm stereo output power at less than 0.1% THD+N: 50W
  • Maximum 8 ohm Bridged-Mono output power at less than 0.1% THD+N: 100W
  • Maximum 70V/100V output power at less than 0.1% THD+N: 30W
  • Frequency Response: 20Hz to 20kHz+/-1Db
  • Impedance: 8 ohm to 4 ohm stable
  • Signal to Noise Ratio: 90dB A-Weighted 1Kz
  • Turn on options: manual on, signal sensing, and 12V Trigger mode
  • Unique bus system distributes a signal from 1 source to multiple locations
  • Input and Output Terminals: zone IR, mute & status terminal, zone speaker terminal, zone line/ bus trigger in, master control in/out, RS232 terminal, zone line in
  • 12 Independent Channels / up to 6 stereo zones
  • Rack Mountable? Yes, rack mount ears included
  • Dual Source Switching? Yes
  • 12 zone mono channels (70V) or 6 stereo zones (8/4 ohm)
  • Dimensions (W x H x D): 16.7" x 4" x 14.25"
  • Weight: 34 lbs
  • Warranty: 2 years
7 Questions asked on PAM1270 12x Channel, 6x Zone 70V/100V/8 Ohm Commercial Multi Combination Amplifier with IR Remote

Oscar • 12/17/2019, 2:17:43 PM Q I bought this item to conect to a Yamaha RX V679 receiver and to make 6 zones for my home. I want to be able to turn and off and to pop up and down the volume of each zone. I understand the IP Addressable RS232 will allow me to do this if I buy a serial controller and a license software to manage this (but his can be pricy just for pup and down volumen and swich off the zones). Anyone can recommend a cheaper solution?
Customer Service • 12/17/2019, 2:17:43 PM
A Hi Oscar: A couple of things you can try, check out "simple control": https://www.simplecontrol.com/support/ They may have some sort of solution for you on the RS232, possible tie in with a computer/laptop. Most of the older laptop actually had a RS232 connector built in. Now they sell RS232 to USB adapters for interface with your computer/Laptop. Here is a link for one of these adapter cables along with a interface you download. https://serialio.com/drivers-and-set-up-usb-rs-232-adapter-in-windows Also there is a remote control that is included with the Amplifier which you can use or a list of all the master code and Hex codes for programming a Universal remote. We can help you jury rig an IR receiver kit where the sensors are hard wired into each of the six zones. You would then connect to the universal Bus so all channels see the same source. You can hard wire each zone as agroup or individual. Please let us know what else you find and contact me at tim@osdaudio.com. Good Luck TL/3881
Oscar • 12/17/2019, 2:17:43 PM Q I bought this item to conect to a Yamaha RX V679 receiver and to make 6 zones for my home. I want to be able to turn and off and to pop up and down the volume of each zone. I understand the IP Addressable RS232 will allow me to do this if I buy a serial controller and a license software to manage this (but his can be pricy just for pup and down volumen and swich off the zones). Anyone can recommend a cheaper solution?
Customer Service • 12/17/2019, 2:17:43 PM
A Thanks for recommendation. This item comes with a small black remote, but this remote does not work. Can u signal how to operate the remote in order to turn on and off the amplifier and select zones and pup up and down the volume? I see the buttons on the remote but I press them nothing happens. Do I have to do anything additional in order to get the remote operating? Oscar
John T. • 12/17/2019, 2:17:43 PM Q I'm currently trying to install the PAM-1270 and have run into a couple of snags. I'm Mac based, but have found a ssh program called Jellyfissh and need to figure out how to use it to communicate the amp to the Mac, and I do have a rs232-usb cable. Basic questions are what is the amps IP address, port and connection type (local,ssh1,ssh2,Telnet,etc.). I'm not a total Luddite , but this ssh stuff is pretty intimidating for me. I'd also like to know what type/model of hard wired IR receivers are recommended so that I can use a remote. Thanks!
Customer Service • 12/17/2019, 2:17:43 PM
A Hi John T: Please contact me directly, we are still trying to sort this out, but would need to communicate directly with you so I can attach info. My email address: tim@osdaudio.com Thanks in advance TL/4027
Alex • 12/17/2019, 2:17:43 PM Q I am planning to install 6 zones with 5 stereo speakers in ceiling (5 rooms) and 2 "mono stereo" in ceiling (2 bathrooms) I have been looking at the Denon Heos drive where I can use an App to controll every room seperatly (different music in all rooms) or combine all the rooms to be able to play the same music in all rooms (for example Spotify). So my question is if the PAM1270 can do the above? Or do I need to combine it with a music streamer of some sort or something else? Thanks, Alex
Customer Service • 12/17/2019, 2:17:43 PM
A Hi Alex: I am not sure if the PAM 1270 would work for your application. I am pretty sure for you to control the DENON Heos for all six zones you will need at least 6 individual links. I am assuming you will have a pair of stereo speakers in 4 rooms and 2 pair in the fifth room. Plus a single stereo/mono speaker in each of your two rooms. That would actually be 7 zones, since each of the stereo/mono speakers are connected to a stereo signal one left and one right to input of the Dual voice coil stereo/mono speaker. Now if you were connecting two speakers in your master bedroom you could connect the master bedroom in parallel to the master bedroom which also means it would play the same music for both but you would now have 6 zones. And you could connect and control six zones with six zones but you would have to sync all six to make them play the same throughout the whole house. That would be a question for DENON. There are other ways of doing this manually but with only two sources based upon what else we can offer. You know Denon has a Heos AMP similar to the SONOS Connect Amp which you would need six or even 7 of them to control your setup. That would be $3,000 to $3,500 US before adding any speakers. Maybe Denon has something else I do not know about but that is what the offer here in the US. Let me know if we can help you further. TL/4550
mark • 12/17/2019, 2:17:43 PM Q looking at this to run 70v , so it is simple to assume you have 12 outputs at 30w each with 12 mono inputs as well?
Customer Service • 12/17/2019, 2:17:43 PM
A Hi Mark: Yes this has 12 mono inputs or six stereo inputs. It also has a bus system that has a mono input so you can have 12 channels from the bus or any combination of bus channels and direct input. You can also do either 70V or 8 ohm or a combination of both. You can also bridge two channels together. The Amp includes a 6 zone IR kit that hard wires into input connector for each zone. That works for all 6 zones. You can add individual IR kits for each zone, these are optional and there is a charge for the additional IR kits. The unit also has RS232 connections. Checkout the owners manual on the web page for info on the IR, RS232 and Bus input. TL/4758