SKU: XMP100
OSD XMP100100W Stereo Power Amplifier Class D, Dual Source, Sub Out, Bass / Treble Control
The XMP100 is the digital Class D version of our popular AMP 120 amplifier. This amp will also power Dolby Surround Sound systems and enhance the power of OSD outdoor speakers. Automatic source switching enables users to connect more than one source to the amp, so, for instance, you could use it to power both a DVD player and an iPod. The XMP100 has the ability to automatically switch sources, as well, if you choose to go from listening to music on your iPod to watching a flick on a DVD player. The power amplifier has 75 watts RMS per channel and bridgeable outputs for 160 watts RMS. An input of 1.4 volts is needed to reach full output and the signal to noise ratio is 107dB (A-weighted). The Dual Source 2-Channel Stereo Amplifier XMP100 has front panel-mounted volume and balance knobs and comes with a two-year warranty.
Connecting Your Smartphone is Easy!
A great feature of the XMP100 is the ability to connect your smartphone, iPod, or other portable music device (as long as it has a headphone jack). The XMP100 includes two RCA signal level inputs marked as red for right and white for left. All you need to do is purchase our inexpensive RCA to mini cable (see RCA audio cables under the audio/video cables tab). The mini 3.5 connector is plugged into the headphone output of your device then the RCAs are connected to one of the inputs of the XMP100. It's that easy!
Warning: California's Proposition 65
Warning:
This product can expose you to chemicals, including vinyl chloride, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
- Power Output: 50WX2 (RMS @ 8Ω)
- Power Output: 75WX2 (RMS @ 4Ω)
- Power Output: 150W (RMS @ 8Ω Bridged)
- Total Harmonic Distortion (THD): <1%(Rated power: 50W @ 8Ω)
- Signal to Noise: >90 dB A WTD
- Frequency Response :20HZ~22KHZ +0/-2dB@ 8Ω
- Adjustable Volume: Min – Max
- Adjustable Bass and Treble: -12~+12dB.
- Line Level Input Sensitivity: 700Mv
- Thermal Protection: Yes
- Short Protection: Yes
- Dimension: 17.28 x 1.73 x 4.96 (WxHxD)
- Weight: 3.3 lbs
View Owner's Manual
39 Questions asked
Have a Questions?
What's on your mind?
Garry • 12/17/2019, 2:17:43 PM
Could this power both a old Bose Series IV and two osd AP840s? The audio source will be and Apple TV with small line amp. I typically run this off a 2x100w Sony 2xchannel receiver.
Customer Service • 12/17/2019, 2:17:43 PM
HI Garry:
The XMP-100 should have no problem powering two 8 ohm pair of speakers. The pair of AP-840 are 8 ohm. The question is on the older BOSE Series IV speakers. Can you confirm these are 8 ohm. Many of the BOSE speakers were 4 ohm. This would create less than a 4 ohm load which might cause a problem when playing both speakers at once.You will also notice that when you push in one of the speaker buttons (either A or B) the other pops out. You can push both in at the same time. We created this safeguard on the original AMP-120 (a class AB amp, a design that has been around for more than 15 years) which is only 50% efficient. We discouraged playing both A and B at the same time on the AMP-120 but not the XMP-100. The XMP-100 is a Digital Amplifier that is 93% Efficient so it creates less heat allowing it to play the lower impedance longer.
TL/4402
Garry • 12/17/2019, 2:17:43 PM
Could this power both a old Bose Series IV and two osd AP840s? The audio source will be and Apple TV with small line amp. I typically run this off a 2x100w Sony 2xchannel receiver.
Customer Service • 12/17/2019, 2:17:43 PM
The Bose is a Acoustimass 5 system with four cube speakers, and one sub. You can see the specs here on page 12: https://assets.bose.com/content/dam/Bose_DAM/Web/consumer_electronics/global/products/speakers/am5_series3/pdf/owg_en_am5_series3.pdf
Garry • 12/17/2019, 2:17:43 PM
Could this power both a old Bose Series IV and two osd AP840s? The audio source will be and Apple TV with small line amp. I typically run this off a 2x100w Sony 2xchannel receiver.
Customer Service • 12/17/2019, 2:17:43 PM
Hi, I provide you a response to your question about the Bose. Can you help confirm it this will be good? I already have the AMP200 powering eight speakers in the yard, tied to your pre-amp so I know that is too much power. thanks.
Garry • 12/17/2019, 2:17:43 PM
Could this power both a old Bose Series IV and two osd AP840s? The audio source will be and Apple TV with small line amp. I typically run this off a 2x100w Sony 2xchannel receiver.
Customer Service • 12/17/2019, 2:17:43 PM
Do you ever plan to answer my question??? I provided you the details you requested...
Chris C • 12/17/2019, 2:17:43 PM
I need to replace a Bose lifestyle 20 system that died. We have Bose outdoor speakers and bookshelf indoor speakers. Is this a good replacement system?
Customer Service • 12/17/2019, 2:17:43 PM
Hi Chris:
The XMP100 should work fine for both your outdoor speakers as well as your bookshelf speakers. My concern was if the BOSE speakers which are part of the System 20 use a speaker wire with a proprietary connector. I looked up the outdoor and bookshelf to confirm the bare wire connection. I also believe this will be a more affordable solution for you. The next step would have been the AMP200.
TL/4460