Filters

Secure Checkout
Free Shipping On Orders Over $50
Your Shopping Cart Is Empty

Secure Checkout

SKU: OSD-PS10 10" High Definition Powered 200W Home Theater Subwoofer Black Wood Veneer, Single Drive - PS10


Purchase 10" High Definition Powered 200W Home Theater Subwoofer Black Wood Veneer, Single Drive - PS10
  • SKU: OSD-PS10 10-inch-premium-powered-subwoofer-ps10

    10" High Definition Powered 200W Home Theater Subwoofer Black Wood Veneer, Single Drive - PS10

  • $169.99

    Compare at: $199.95 You Save $29.96

    In Stock

Calculate Shipping

Guarantee

Lifetime Tech Support

The PS10 subwoofer is a free-standing and fully powered 10-inch subwoofer and an excellent addition to any collection. This is an ideal subwoofer for a home theater or a small to medium size room where you wish to have full, powerful sound. Surround yourself with the most realistic sounds and put yourself in the center of the action during any movie, music experience or casual listening with the lower frequency range of this powerful subwoofer. This subwoofer, which covers a 30 Hz to 120 Hz range, features a front firing woofer in dual front firing ports, so you can build it into a custom cabinet. The OSD Audio PS10 high performance home theater subwoofer has speaker level inputs and delivers 200 watts of power. 

Warning: California's Proposition 65

Warning:

 This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP) which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov


  • Woofer: 10" 
  • Frequency Response: 30Hz to 120Hz 
  • Power Handling: 200W
  • Impedance: 8 Ohms
  • Phase: 0-180°
  • Inputs: L&R / Low Level
  • Sold As: Single
  • Unit Dimensions: (L x H x D) 13.5" x 14" x 15"
  • Weight: 19.5 lbs
15 Questions asked on 10" High Definition Powered 200W Home Theater Subwoofer Black Wood Veneer, Single Drive - PS10

Jim • 12/17/2019, 2:17:43 PM Q Can you tell me what this subwoofer weighs? It's not listed. There are no dimensions specified either. Lastly, what's the true frequency response? It says 5Hz-180Hz, but it can't possibly get down to 5Hz.
Customer Service • 12/17/2019, 2:17:43 PM
A Weight for both the PS-10 and PS-12 appear in the download Tab-Owners Manual: Net Weight (out of the shipping box): 29.17 lbs Gross Weight (with all the packing material): 36.38lbs The manual does not give you dimensions for the PS-10 but here they are: PS-10: 13 1/2" L x 14 1/4" D x 13 1/2" H (plus 2"or 15 1/2"H with feet) Regarding the both the PS-10 and PS-12 Frequency Response of 5Hz to 180Hz The true specification should be 25Hz to 180Hz.. We are making the corrections to our owners manual, product information and our web site. Both the PS-10 and PS-12 Subs were created for Home Theater applications where they are connected to the LFE output of the AV receiver. Both subs have no problem working with whatever you can dial up for low frequency effects. One of the advantages of the Front firing Speaker and Port design is that it allows you to build it into a custom media center cabinet. This along with the Auto-on sensing allows you to set it and forget it. Plus under downloads next to the Owners Manual, check out our Product information PDF for our Down firing Subwoofer versus Front firing Subwoofer comparison. Also see link below for Review from Home Theater forum: http://www.hometheaterforum.com/t/315777/osd-audio-ps10-high-powered-10-subwoofer-review Note: We will notify Home Theater Forum of the specification change as well. TL/MA
Jim • 12/17/2019, 2:17:43 PM Q Can you tell me what this subwoofer weighs? It's not listed. There are no dimensions specified either. Lastly, what's the true frequency response? It says 5Hz-180Hz, but it can't possibly get down to 5Hz.
Customer Service • 12/17/2019, 2:17:43 PM
A Weight for both the PS-10 and PS-12 appear in the download Tab-Owners Manual: Net Weight (out of the shipping box): 29.17 lbs Gross Weight (with all the packing material): 36.38lbs The manual does not give you dimensions for the PS-10 but here they are: PS-10: 13 1/2" L x 14 1/4" D x 13 1/2" H (plus 2"or 15 1/2"H with feet) Regarding the both the PS-10 and PS-12 Frequency Response of 5Hz to 180Hz The true specification should be 25Hz to 180Hz.. We are making the corrections to our owners manual, product information and our web site. Both the PS-10 and PS-12 Subs were created for Home Theater applications where they are connected to the LFE output of the AV receiver. Both subs have no problem working with whatever you can dial up for low frequency effects. One of the advantages of the Front firing Speaker and Port design is that it allows you to build it into a custom media center cabinet. This along with the Auto-on sensing allows you to set it and forget it. Plus under downloads next to the Owners Manual, check out our Product information PDF for our Down firing Subwoofer versus Front firing Subwoofer comparison. Also see link below for Review from Home Theater forum: http://www.hometheaterforum.com/t/315777/osd-audio-ps10-high-powered-10-subwoofer-review Note: We will notify Home Theater Forum of the specification change as well. TL/MA
Kevin • 12/17/2019, 2:17:43 PM Q I have a Yamaha Rx-A710 and That I am building a whole house audio around. My house is prewired, and my subwoofer outlet is wired with 4 wire speaker wire instead of RCA connections. So I can't use the subwoofer RCA output on the Yamaha receiver to connect a PS 10 (unless I run a subwoofer cable outside the wall - which I perfer not to do for asthetics) . Which R and L level Line speaker outlets on the A710 should I connect the subwoofer to (I will be doing a 6.1 surround sound so I only have one open speaker connection --the right back surround sound)? Do Ihave to do stero to the subwoofer if use a level line connection? Can I hook more than one speaker to each connection on the back of the A710? Thanks.
Customer Service • 12/17/2019, 2:17:43 PM
A Hi Kevin, I feel your pain. There may be a solution but you may have to verify this with Yamaha, the manufacturer of the receiver. First, are you using the Zone 2 Speaker outputs also listed as zone2-prescenece? You did not mention doing anything other than powering the 6.1 system. If that is true you may be able to connect the four conductors to the speaker level outputs listed as zone 2-prescence. Then from your wall plate, connect to the speaker level inputs (right and left)of the PS-10 Sub-woofer, making sure to connect positive to positive and negative to negative. In the configuration (see page 91 in your manual), make sure you enable the presence connection and then disable sub-woofer (no sub connected). Once the sub-woofer output shows disconnected, the low frequencies are converted to LFE and channeled through the front-stage speakers which I am assuming includes the presence speakers. On the subwoofer itself, you will set the high cut filter to half way and set the gain level to match your standard listening levels. Once you set it, the volume will be controlled by the receiver. You should call Yamaha support to ask them if this is possible. The problem you would have using channel seven is the surround frequency for the side centers might not be full range, thus limiting low frequencies to your sub. I hope that is not too confusing. I attended a Yamaha training just yesterday and learned about the presence. Too bad I did not have your question earlier or I would have asked their specialists. In theory this should work, pretty cool. Good luck... TL/MA
Kevin • 12/17/2019, 2:17:43 PM Q Thanks for responding so quickly. I will be connecting a OSD AMP 200 to zone 2 on the A710 to power dual speakers in the bedroom, dining room, and outside patio, so I can't zone 2 as you recommended. However, the AMP 200 will be connected to a DSM4 speaker selector which will have an unused zone. Could I connect the PS10 (using level line) to this empty zone on the DSM4 as "speaker selector A" position will be transmitting what is playing through my home theater system?Thanks for responding so quickly. I will be connecting a OSD AMP 200 to zone 2 on the A710 to power dual speakers in the bedroom, dining room, and outside patio, so I can't zone 2 as you recommended. However, the AMP 200 will be connected to a DSM4 speaker selector which will have an unused zone. Could I connect the PS10 (using level line) to this empty zone on the DSM4 as "speaker selector A" position will be transmitting what is playing through my home theater system?
Customer Service • 12/17/2019, 2:17:43 PM
A Hi Kevin: Based upon your response there maybe a solution for your application that can be implemented with out adding anything (using what you have already) to your system. Again I am assuming you are only connecting a single source (Zone two audio output from the Yamaha Receiver) to the AMP200. If that is the case then you may be able to connect the dedicated subwoofer output from the Yamaha directly to the input #2 of the AMP200 with a combination of single subwoofer cable and a single Female RCA to dual Male RCA Y Adapter so you can plug in a single connector to the (mono) subwoofer output of the Yamaha Receiver. Then use the Y adapter to connect to both the Right and left input on input #2. Now connect one end of the the four conductor cable to Speaker B output of the AMP200 and the other end (coming out of the wall in your Home Theater room) to the Right and Left (+/-) input of the PS10 Powered Sub-woofer. Here is the trade off... you would be able to play your Home Theater System with your Sub-woofer operating as the .1 of the 6.1 system. This is also hoping you will have enough speaker connections pre-wired into the room to accommodate the six channels plus two more for the Sub. But you would only be able to listen to the Home Theater (Zone 2 would have to be off) since you would need to make sure the AMP200 has no signal into input (or source) #1. Input #2 only plays if input #1 is inactive. But you would have the subwoofer be active as intended for a true 6.1 system. I am thinking with the Yamaha you have the ability to play both the Home Theater System and Zone 2 at the same time but you will have to defeat the Sub-woofer output from the Yamaha remote so it adds the LFE (Low Frequency Effects) through the Front stage speakers (the Left, Center and Right speaker). It would be a bit of a compromise versus having the PS-10 active in the system but you would be able to play both the Home Theater and Zone 2 whole house at the same time. Please let me know what you think... Good luck TL
Vasanth • 12/17/2019, 2:17:43 PM Q I'm interested in buying this sub but as I live in India, wanted to confirm that the power supply supports (220V @50) (Shipping to India will be taken care :-) )
Customer Service • 12/17/2019, 2:17:43 PM
A Hi Vasanth, Like many OSD products, the PS10 home theater subwoofer includes a 220V switch for use in other countries. CL/MA 1472