SKU: KIT-MX880x2
2x MX880 Bundle, 4x Source, 8x Zones Combined
Our MX880 is a powerful 4-zone 8-channel digital amplifier for commercial and residential audio systems that require reliable power in multiple zones. And now you can purchase a bundle of 2 of them allowing you to have 8-zones, 16 channels of reliable power and audio signal sent around larger homes or commercial buildings. A slim 2U, rack-mountable and cool-running multi-room amplifier, each MX880 includes eight channels rated at 80 Watts RMS each at 4 ohms/50 watts RMS at 8-ohms and can be configured as the main amplifier for an audio distribution system such as for background music, paging, and multi-zone audio or as an amplifier for 5.1 or 7.2 home theater surround sound systems.
Features:
- High power 4-zone/8-channel amplifier that supplies audiophile-level sound to distributed audio systems and home theaters
- Provides 80 Watts per channel RMS (1KHz into 4 Ohms), 50W Watts per channel RMS (1KHz into 8 Ohms)
- Uses highly-efficient Class D technology that runs cooler and keeps distortion low
- Independent 4-zone control with global and independent zone triggering
- Includes a bridged switch per each zone; both channels can be bridged internally with a single connection (left input) output (160 watts at 8 ohms)
- Special protection circuitry safeguards the amplifier from thermal overload and short circuits
- Includes Bus Global 12V Trigger and Dual Bus Inputs/Outputs
- Signal auto-sensing detects a signal to power up and powers down when a signal is not detected
- Pair with the NERO Link Streaming Module for the ultimate setup
- Front-panel status indicators
- Rack-mountable with hardware included
Designed for Installation Flexibility
The MX880 accommodates a wide range of audio applications with global and independent zone triggering, audio sense circuitry with adjustable gain/vol per channel, two Bus Inputs/Outputs and independent left and right line inputs per zone. With high performance and ultra-low distortion output, the MX880 Multi-Zone Amplifier provides unmatched sound quality for any audio system.
Class D Efficiency
Our MX880 uses highly efficient Class D digital circuitry. Class D amplifiers use output transistors that are fully turned on or off during operation, which keeps distortion low and efficiency is high (93%). Class D amps combine the best qualities of both class A and B technologies and are ideal for distributed audio and home theater setups because these amps run cooler than traditional amps and can easily run multiple pairs of speakers at a 4-ohm or 8-ohm load.
Bridgeable with Independent Zone Control
When used with an audio distribution preamp or matrix processor, each zone can independently drive one of several different sources by using each zone’s line audio inputs, and if a particular area needs higher power, then two zones can be bridged for 160 watts per channel x 2 at 8 ohms.
Warning: California's Proposition 65
Warning:
This product can expose you to chemicals, including vinyl chloride, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
- Amplifier Type: Multi Channel
- Amplifier Class: Class D
- Channels: 8 Each; 4 Stereo Zones
- Power Handling: 50W(RMS)/ 100W(MAX) Per Channel @ 8 Ohm
- Power Handling: 80W(RMS)/ 160W(MAX) Per Channel @ 4 Ohm
- Bridged Rating (Watts): 320W(MAX) @ 8 Ohm
- Impedance: 8 Ohm and 4 Ohm Stable
- Frequency Response: 20Hz to 20KHz + 1.7/-1dB at 1W output into 8 Ohms
- Signal to Noise Ratio: 90 dB A-weighted
- 12V Trigger Mode, Bus
- Zone Line Input: Line In, Bus In 1, Bus In 2 Per Zone
- Individual Output Level Controls for Each Channel
- Speaker Connectors: Detachable Speaker Terminals, up to 14AWG
- Rack Mountable: Yes
- Dimensions (L x H x D): 16.81" x 3.46" x 16.41"
- Weight: 19 lbs
- Warranty: 2 Years
View Product Information
No Questions asked yet!