Filters

Secure Checkout
Free Shipping On Orders Over $50
Your Shopping Cart Is Empty

Secure Checkout

SKU: OSD-ATM-7 7 Zone Automatic Speaker Selector w/ Remote Control IR Code - ATM7


Purchase 7 Zone Automatic Speaker Selector w/ Remote Control IR Code - ATM7
  • SKU: OSD-ATM-7 7-pair-speaker-selector-with-remote-control

    7 Zone Automatic Speaker Selector w/ Remote Control IR Code - ATM7

  • $218.99

    Compare at: $399.95 You Save $180.96

    In Stock

Calculate Shipping

Guarantee

Lifetime Tech Support

New improved we dim the blue led indicator light so it is not too bright at night. Speaker selector switches allow you to connect multiple pairs of speakers to your stereo receiver or amplifier. The ATM 7-Zone Speaker Selector with Remote Control can control up to seven pairs of speakers so you can listen to music in multiple rooms simultaneously.

ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.

Warning: California's Proposition 65

Warning:

This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP) which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

  • Speaker Selector Type: 7 Zone Speaker Selector w/ IR Remote Control
  • # of Zones or Speaker Pairs: 7
  • Single Source
  • Impedance Protection: No
  • Maximum Operating Range: 400W
  • Input Source: 7 Inputs to Speaker A/B or 2 Sources to 7 Zones
  • Input/ Output Connector Type: Multi-way Binding Posts
  • Last Call Back-up Memory Function
  • Rack Mountable: Yes, 1.5RU
  • Remote Control: Yes
  • Dimensions (L x H x D): 16.5" x 3" x 7.87"
  • Weight: 7 lbs
  • Warranty: 2 Years
  • The ATM7 does not have any Internal Impedance Matching Protection
  • Note: We recommend adding Impedance Matching Volume Controls for each zone if you are planning to play more than two 8-ohm pairs of speakers at the same time.

Infrared Emitter Information and Installation Guide:

  • With 5 meters cable length
  • With 3.5mm mono standard plug
  • With self-adhesive tape for quick and easy fixing on any hard, clean & dry surface.
113 Questions asked on 7 Zone Automatic Speaker Selector w/ Remote Control IR Code - ATM7

Jmaple168 • 12/17/2019, 2:17:43 PM Q Does the speaker binding posts accept spade connectors? I have very expensive speaker cables with only spade terminations.
Customer Service • 12/17/2019, 2:17:43 PM
A It is built to accept banana plug or bare wire. You may be able to get spade connections to work somehow, but we do not offer any solutions for spade connectors unfortunately.
Jmaple168 • 12/17/2019, 2:17:43 PM Q Does the speaker binding posts accept spade connectors? I have very expensive speaker cables with only spade terminations.
Customer Service • 12/17/2019, 2:17:43 PM
A Buy female spade connectors and crimp them on to some speaker wire. then run the wire to the selector wire lugs.
CR • 12/17/2019, 2:17:43 PM Q Ok, I am interested in this selector as it has remote control. It will drive 5 pairs of speakers. My source is the Zone2 out from a surround amp. What AMP would you suggest? The AMP200 or AMP300? I am not looking for wild power. I just want something that can handle the impendance load that could happen if all speakers are turned on. Thank you.
Customer Service • 12/17/2019, 2:17:43 PM
A Hi CR, Either the AMP200 or AMP300 will work, but you will have limited volume on the 200, as running 4-5 zones is going to be utilizing all of its power. The AMP300 has some extra juice for you to really get a lot of power with 5 pairs.
Joe • 12/17/2019, 2:17:43 PM Q Is it possible to control the speaker selector with a iPhone, iPad ect?
Customer Service • 12/17/2019, 2:17:43 PM
A Hi Joe, The speaker selector require and amp to feed it power. You can run any handheld device such as an iPhone or iPad to the amp, but not directly to the speaker selector, as it is a passive device. The power supply for the speaker selector is only there to power the LED lights. Any speakers will need to be driven by an amp running to the selector.
Joe • 12/17/2019, 2:17:43 PM Q Is it possible to control the speaker selector with a iPhone, iPad ect?
Customer Service • 12/17/2019, 2:17:43 PM
A Yes. It is possible. The ATM-7 is recognized by the Logitech smart remote which has a smart phone app built in. I've successfully set this up where you can use your phone or tablet to change zones. Only device on the market that will do this at this cost.