Filters

Secure Checkout
Free Shipping On Orders Over $50
Your Shopping Cart Is Empty

Secure Checkout

SKU: OSD-ATM-7 7 Zone Automatic Speaker Selector w/ Remote Control IR Code - ATM7


Purchase 7 Zone Automatic Speaker Selector w/ Remote Control IR Code - ATM7
  • SKU: OSD-ATM-7 7-pair-speaker-selector-with-remote-control

    7 Zone Automatic Speaker Selector w/ Remote Control IR Code - ATM7

  • $218.99

    Compare at: $399.95 You Save $180.96

    In Stock

Calculate Shipping

Guarantee

Lifetime Tech Support

New improved we dim the blue led indicator light so it is not too bright at night. Speaker selector switches allow you to connect multiple pairs of speakers to your stereo receiver or amplifier. The ATM 7-Zone Speaker Selector with Remote Control can control up to seven pairs of speakers so you can listen to music in multiple rooms simultaneously.

ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.

Warning: California's Proposition 65

Warning:

This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP) which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

  • Speaker Selector Type: 7 Zone Speaker Selector w/ IR Remote Control
  • # of Zones or Speaker Pairs: 7
  • Single Source
  • Impedance Protection: No
  • Maximum Operating Range: 400W
  • Input Source: 7 Inputs to Speaker A/B or 2 Sources to 7 Zones
  • Input/ Output Connector Type: Multi-way Binding Posts
  • Last Call Back-up Memory Function
  • Rack Mountable: Yes, 1.5RU
  • Remote Control: Yes
  • Dimensions (L x H x D): 16.5" x 3" x 7.87"
  • Weight: 7 lbs
  • Warranty: 2 Years
  • The ATM7 does not have any Internal Impedance Matching Protection
  • Note: We recommend adding Impedance Matching Volume Controls for each zone if you are planning to play more than two 8-ohm pairs of speakers at the same time.

Infrared Emitter Information and Installation Guide:

  • With 5 meters cable length
  • With 3.5mm mono standard plug
  • With self-adhesive tape for quick and easy fixing on any hard, clean & dry surface.
113 Questions asked on 7 Zone Automatic Speaker Selector w/ Remote Control IR Code - ATM7

james • 12/17/2019, 2:17:43 PM Q i see that there is not a ON/OFF for the remote. Wonder if there is a IR code out there for it from the manufacture. I was thinking that if your AMP has a switched outlet that your could control it that way?? Anyone use it with a URC remote?
Customer Service • 12/17/2019, 2:17:43 PM
A Hi James: The ATM7 does not have a 12 volt trigger that would be needed to connect directly to an Amplifier like our AMP200 or multi-channel amp the MX1260. It does have an IR Receiver input so you can hard wire a IR Receiver to it. We are attempting to get the actual code from the Factory, but you should be able to learn the code form the existing remote using any Universal Remote Like URC. We will post the code once we get it on the site. TL/3111
Dan • 12/17/2019, 2:17:43 PM Q I currently have two AMP120s connected to Zone 2 on my receiver, running four sets of speakers total. I need to be able to play 2x sets simultaneously maximum. I want to be able to control what zones are on via IR so am looking at the ATM7. I see I can connect both of the AMP 120s to the ATM7 but it looks like only one can be active at time. Is there any way with two amps that I can get two zones of speakers active simultaneously using the ATM7? If not, any other ideas? Thanks and love your products!
Customer Service • 12/17/2019, 2:17:43 PM
A Hi Dan: Typically the AMP120 features A and B speaker output but the speaker switches purposely allow you to only have one set of speakers to play at one time. I am assuming you have decent AVR that not only features a zone 2 output but allows you to control the receiver with a universal remote or application that will allow you to use a number of different devices. Also you did not mention that you are using volume controls to help control the impedance. I do have a suggestion using your two AMP120 amplifiers. You should checkout our SSVC4 speaker selector. It features an internal Volume control per zone to control the impedance matching. The SSVC4 also features Dual source selectable by zone so you can listen to two different sources at the same time. Say zone one would be source A and zones 2, 3 and 4 could be playing source B. The way you would configure the AMP120 would be as follows. Connect Zone 2 output of the AVR to the first AMP120 (source A) to the Input 2. Then connect the second AMP120 (source B) from the first AMP120 Line 2 Output to the In-put #2 of the second AMP120.You can then add a second actual source to Line Input #1 of the Second AMP120.. You would then connect the first AMP120 Speaker A to Source A of the SSVC4. The Second AMP120 speaker B Output would be connected to the Source B of the SSVC4. Make sure the first AMP120 has the speaker A button pushed in and AMP120 has speaker Button B pushed in. I can provide you an actual diagram if you want just let me know if you want a further explanation. Good Luck TL/3152
garrett • 12/17/2019, 2:17:43 PM Q I have a Pioneer VSX-518-K 5-Channel A/V Receiver Featuring Advanced Sound Retriever Can I hook this to it in order to utilize my outdoor speakers I have added in my backyard. There are 4 sets of speakers and planning to add some in sunroom. Thanks
Customer Service • 12/17/2019, 2:17:43 PM
A Hi Garrett, You can, but we don't recommend it. This is intended for use with a high-current amplifier such as our AMP300. This unit doesn't have any kind of impedance protection, so it would be very risky running it off your 8ohm receiver. You could run your receiver into our AMP300 and run the ATM-7 off our AMP300 to power your outdoor system.
Lloyd Piper • 12/17/2019, 2:17:43 PM Q The manual says there are rack mounting ears available for this product. I don't see any on the OSD web site? Where can I buy rack mounting ears? It would help my application to rack-mount this product.
Customer Service • 12/17/2019, 2:17:43 PM
A Hi Lloyd, I don't believe this unit is rack mountable, or at least doesn't have specific rack mounts. I didn't see this in the manual, can you tell me which page/section?
Greg • 12/17/2019, 2:17:43 PM Q Can I use this to switch which speakers are active for a sons connect:amp? I'd like to have one connect:amp play in different rooms, but not at the same time. Thanks!
Customer Service • 12/17/2019, 2:17:43 PM
A Hello Greg, That is the function of this unit, but it doesn't have any impedance protection, so unless your Sonos amp can run less than an 8ohm load (4ohm - 2ohm) then you would need to run impedance matching volume controls for each set of speakers.