Filters
Product Search

    Secure Checkout
    Your Shopping Cart Is Empty

    Secure Checkout

    SKU: OSD-ATM-7

    OSD ATM77x Zone Automatic Speaker Selector w/ Remote Control IR Code

    Purchase 7x Zone Automatic Speaker Selector w/ Remote Control IR Code ATM7
    • Outdoor Speaker Depot SKU: OSD-ATM-7 7-pair-speaker-selector-with-remote-control
    • In Stock

      $199.99

      Compare at: $416.99
      You Save: $217

    • Countdown Truck
      FREE Delivery by ,
      Order within hours and minutes
      Change Shipping Zip ? Free Shipping Over $50
      More Delivery Options

    Lifetime Tech Support

    Guarantee

    Lifetime Tech Support

    New improved we dim the blue led indicator light so it is not too bright at night. Speaker selector switches allow you to connect multiple pairs of speakers to your stereo receiver or amplifier. The ATM 7-Zone Speaker Selector with Remote Control can control up to seven pairs of speakers so you can listen to music in multiple rooms simultaneously.

    ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.

    Warning: California's Proposition 65

    Warning:

    This product can expose you to chemicals, including vinyl chloride, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.

    • Speaker Selector Type: 7 Zone Speaker Selector w/ IR Remote Control
    • # of Zones or Speaker Pairs: 7
    • Single Source
    • Impedance Protection: No
    • Maximum Operating Range: 400W
    • Input Source: 7 Inputs to Speaker A/B or 2 Sources to 7 Zones
    • Input/ Output Connector Type: Multi-way Binding Posts
    • Last Call Back-up Memory Function
    • Rack Mountable: Yes, 1.5RU
    • Remote Control: Yes
    • Dimensions (L x H x D): 16.5" x 3" x 7.87"
    • Weight: 7 lbs
    • Warranty: 2 Years
    • The ATM7 does not have any Internal Impedance Matching Protection
    • Note: We recommend adding Impedance Matching Volume Controls for each zone if you are planning to play more than two 8-ohm pairs of speakers at the same time.

    Infrared Emitter Information and Installation Guide:

    • With 5 meters cable length
    • With 3.5mm mono standard plug
    • With self-adhesive tape for quick and easy fixing on any hard, clean & dry surface.
    113 Questions asked
    Have a Questions?

    What's on your mind?


    Lew • 12/17/2019, 2:17:43 PM Hello, I want to have options for activating a pair (front L&R, rear L&R) of ATMOS in-ceiling speakers depending upon where I am sitting in my 3 row theater seating. The source is the ANTHEM 1120 receiver (see first image) that outputs front L&R and rear L&R 'height speakers'. Those would be switched as depicted in the second image.. Important must-haves: 1) No degradation at all of the sound from the ANTHEM to the speakers. 2) IR remote control, programmed into my URC universal remote, so that I can select the active pair of height speakers from my theater seats. Will the ATM7 do the job? Please don't hesitate to ask questions. Thank you.
    Customer Service • 12/17/2019, 2:17:43 PM
    Hi Lew: Your images did not come through (please try sending to tim@osdaudio.com). Are you trying to control the front height and rear speakers so you can turn front on only, or Rear on only or have both play together? The ATM has dual source input so you can hook up front height to source A and Rear Height to Source B. And you can pick either A or B to play but not both at once. We have dual source selectors with A/B switch per zone but these are manual switchers with no remote control (IR, RF or Wi-Fi connections). So the ATM would not work for your application. TL/4770
    Tim • 12/17/2019, 2:17:43 PM Hi I am running 2 Monoblocks and would like the ability to switch between 2 sets of speakers . One set are my main SVS floor standing speakers and one set are book shelf speakers with banana plug connectors. How can I do this?
    Customer Service • 12/17/2019, 2:17:43 PM
    Hi Tim: I am assuming you are looking at the ATM7 for its remote control capability. There is no problem connecting two speakers to the two mono blocks. You can even run both pair of speakers at the same time assuming you Mono blocks have no problem seeing 4 ohm load. Check to see what you speakers are rated at 8 or 4 ohm. Note there is no internal protection with the ATM7 so you would not be able to run a third pair of speakers (The ATM 7 has 7 zones total.) with the first two without adding Impedance Matching Volume Controls on all pairs of speakers. So yes you can run both pair of speakers (as long as they are 8 ohm) at the same time with no problem. Good luck: TL/4816
    Todd Welliver • 12/17/2019, 2:17:43 PM Doing a Home automation project, with speakers throughout the house. roughly 7 speakers 2 will be in pairs. ( these 2 pairs will be shared by 2 recievers, others remaining single speakers done through single receiver). I have Niles SAS-1 ( auto sensing switch) and Niles SPK-1 ( voltage sensing switch via 12 volt trigger out) which will help share 2 different receivers labeled "A" and "B". Here is my question can I direct which speakers get activated in one room and not every speaker on the speaker selector, vs all the speakers at once in every room?? The Home automation can be setup to control IR controlled items as this one Any help would be appreciated Diagrams are also appreciated. Speaker Specs Specifications Frequency Range: 40Hz – 22kHz +/- 6dB Crossover: 12dB/octive (low pass), 6dB/ octive (mid pass), 12dB/octive (high pass) Sensitivity: 90dB (1W/ 1m) Power Handling: 200 Watts peak Drivers: 1 – 1â€? Neodymium soft dome pivoting tweeter, 1 – 1.5â€? Soft dome midrange driver, 1 – 8â€? 15Ëš angled Kevlar woofer Magnet: 22- ounce ferrite magnet Impedance: 8 ohms
    Not yet Answered.
    paolo marcellini • 12/17/2019, 2:17:43 PM Hi, is it possible to connect three or more amplifiers to two pairs of loudspeakers? Thank you. Paolo Marcellini
    Customer Service • 12/17/2019, 2:17:43 PM
    Hi Paolo: The ATM7 is a 7 zone speaker selector connected to two sources. It has a Master Source A or B switch. You can only play one source up to 7 zones. It is bi-directional, so you can connect up to 7 amplifiers and drive two pairs of speakers, but the A/ B source switch is limited to playing zone 1 (source A) or Zone 2 (source B). Note there is no protection (Impedance Matching capability) for the 7 zones but is not an issue when connecting the two speakers (A/B) and up to 7 amps (you can only select one amp to play at a time (the ATM 7 does not mix the signals). I hope that helps. The ATM7 also features an IR Remote control. TL/5187
    Gus • 12/17/2019, 2:17:43 PM I have a house with 6 pairs of speaker one pair in each room all wired with in wall speakers and volume control. Does this unit would work with what I have? Also I'm assuming I would need to connect a sound source to this unit. what you guys recommend so I can control using my smartphone or even a tablet? thanks
    Customer Service • 12/17/2019, 2:17:43 PM
    HI Gus: The ATM7 will work for your application. You already have your six zones covered including speakers and Impedance Matching Volume Controls> The ATM7 will help you organize your wiring which should be home run back to a central location. You will need an amplifier like our AMP200 and the Pre-One preamplifier. At that point, you will need to decide what source you want to add. There are also some choices for you to pick from that will provide streaming content that you will be able to control with an app on any number of devices including your Smartphone or Tablet. Check out the SONOS Connect, AMAZON Alexa, Any number of Bluetooth dongles (online) or something like the Chromecast Audio. With the Pre-One you can connect a number of these and other older components like a turntable, CD player, DVD player or even an old laptop. Please let me kno=w if you need additional help; tim@osdaudio.com. TL/5206