SKU: OSD-ATM-7
OSD ATM77x Zone Automatic Speaker Selector w/ Remote Control IR Code
New improved we dim the blue led indicator light so it is not too bright at night. Speaker selector switches allow you to connect multiple pairs of speakers to your stereo receiver or amplifier. The ATM 7-Zone Speaker Selector with Remote Control can control up to seven pairs of speakers so you can listen to music in multiple rooms simultaneously.
ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.
ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.
Warning: California's Proposition 65
Warning:
This product can expose you to chemicals, including vinyl chloride, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
- Speaker Selector Type: 7 Zone Speaker Selector w/ IR Remote Control
- # of Zones or Speaker Pairs: 7
- Single Source
- Impedance Protection: No
- Maximum Operating Range: 400W
- Input Source: 7 Inputs to Speaker A/B or 2 Sources to 7 Zones
- Input/ Output Connector Type: Multi-way Binding Posts
- Last Call Back-up Memory Function
- Rack Mountable: Yes, 1.5RU
- Remote Control: Yes
- Dimensions (L x H x D): 16.5" x 3" x 7.87"
- Weight: 7 lbs
- Warranty: 2 Years
- The ATM7 does not have any Internal Impedance Matching Protection
- Note: We recommend adding Impedance Matching Volume Controls for each zone if you are planning to play more than two 8-ohm pairs of speakers at the same time.
- With 5 meters cable length
- With 3.5mm mono standard plug
- With self-adhesive tape for quick and easy fixing on any hard, clean & dry surface.
View Owner's Manual
113 Questions asked
Have a Questions?
What's on your mind?
javier • 12/17/2019, 2:17:43 PM
does thie atm7 conects directly in the bose receiver in the auxiliary audio input jacket?
Customer Service • 12/17/2019, 2:17:43 PM
HI Javier:
The ATM 7 has only speaker level ( High level) inputs and outputs. It has to connect to either Speaker A or Speaker B of the BOSE amplifier. You also have to make sure you utilize Impedance matching Volume Controls for each speaker that you connect to the ATM7. The Speaker Selector has no internal Impedance Matching and if you were to connect two pair or more and play at the same time the BOSE Receiver would have issues with the lower impedance. The problem is when the impedance drops the current demand increases and the more current the greater amount of heat is created. If your receiver is only rated at 4 ohms it will not handle the current draw or the excess heat created.
TL/4222
Chris • 12/17/2019, 2:17:43 PM
Problem in operating the OSD-ATM7.
When I turn on the OSD ATM-7 and then click on the "zone out / in Selector" 1,2,3 ... ..7 , after 30 seconds to up to 2 minutes, you hear a relay click and the OSD ATM-7 turns off the respective speakers , Also the yellow led goes out. This does not change automatically, therefore you have to press manually the appropriate selector button.If you turn the device off and on again, it will remember the last setting and will function up to 2 minutes. If I use "Multi Zone In / Out", I can turn on multiple speakers at a time (1 -7), and what happens than is actually the same, so after a maximum of 2 minutes, the multiple speakers with corresponding yellow LEDs will turn off. If you do it the other way around, so "IN / OUT Mode" changes, you see exactly the same mistake. Finally, I disconnected all cabling, so both the inputs and outputs and the OSD ATM-7 turned on, and after 2 minutes the speakers 1 - 7 with the yellow LEDs are also released.There I love the OSD to operate I hereby ask you, ca you give me an answer what the problem may be. If this ain’t possible, I wonder if it is possible to send me a Service Manual. Hope to hear from you soon.
Kind regards,
Chris Willems
Customer Service • 12/17/2019, 2:17:43 PM
Hi Chris:
I am sorry you are having issues.
I need a little more information to better address your problem;
1) What is your configuration; how many speakers, one or two sources?
2) Has the system worked as it should then started to act up or is this an out of box problem?
3) Zone in/Out Select, I am assuming you are connecting two sources?
4) Based upon what you describe it sounds like a defective unit. Which based upon where you are is a problem (Holland?)
5) Where and when did you purchase the unit from?
6) Did you download the owner's manual from our site?
I will send an email regarding your problem to the factory and request a possible service manual if available.
My email address is tim@osdaudio.com
TL/4381
Dax • 12/17/2019, 2:17:43 PM
I'm not too familiar with audio equipment, so please be patient.
I am wanting to replace my current Russound speaker selector with this one, because the Russound doesn't isn't remote controlled. I currently can just tell Alexa to connect to my AVR and play whatever throughout my home. She can also change from the AVR Main Zone to Zone 2, change the source, and change the volume. What she can't do currently is select which speakers to play from. I have to manually go into our library and change that one thing. It's no big deal, but it's one of those things where having to go do that one thing makes having the other conveniences sort of moot.
So, my question is about the note above Note. Use impedance matching volume controls with this unit." Is this something I need to worry about? We do not have in-wall volume control. I wish we could control each room's volume, but we don't currently and it's not a big deal. Sound comes from the selected source to the avr to the amp to the speaker selector through the walls to the speakers.
Thanks
Customer Service • 12/17/2019, 2:17:43 PM
Hi Dax:
There is an issue withe ATM7 not having internal impedance protection in case you want to listen to more than two pair of speakers at a time. So we recommend having to use the Impedance Matching Volume Controls to make sure the amp/receiver does not see a impedance load less than 4 ohms.Most Receivers and Amps want to see a 8/16 ohms load. It is not a big problem if you are using a High Current amplifier like our AMP200 and AMP300. but their limit is between 3 and 4 pair.
TL/4459
Andre Dueso • 12/17/2019, 2:17:43 PM
Do you deliver products in Mexico?
Thks for yr answer
Andre Dueso
Customer Service • 12/17/2019, 2:17:43 PM
Hi Andre:
Yes we do ship to Mexico. The only difference is we do not have free shipping to Mexico.
TL/4479
Marlene • 12/17/2019, 2:17:43 PM
I recently purchased the ATM7 and connected it to my receiver and speakers; however, I am not able to change the volume in any of the speakers.
Customer Service • 12/17/2019, 2:17:43 PM
Hi Marlene:
This unit is a unique speaker selector that with its remote control you can select which speaker you want to turn off or on, there is no individual or master volume control on either the Box or the remote. It is just a speaker selector that connects all your speakers together in parallel. And the ATM7 allows yo to do it remotely.
Sorry about that...
TL/4488